How to Install Replacement Projector Lamps
Replacing projector bulbs is't difficult, but it does require some basic knowledge about what type of lamp you have, how long it should last and how to remove it. Most projector lamps need to be replaced after around 2,000 hours, while some may have longer or shorter lifespans based on the model of the lamp. To get an estimate on how long your projector bulb should last, consult the user manual for more information. For specific details on bulb replacement, please consult our Library of Owner's Manuals to find your brand/model of projector.
The first step in replacing a lamp is to determine what style you need. MyProjectorLamps sells the following lamp styles:
- Projector Lamp with Module
This style of projector lamp consists of the bulb, the electrical wiring and the plastic casing that surrounds them. The bulb is clipped into place and then locked into the casing with a few screws in the back.
- Bare Projector Lamps
A bare projector lamp includes just the bulb on it's own, without the addition of the plastic casing, wiring and screws.
Installing a Projector Lamp w/Module
1. Make sure the projector is unplugged and sitting on a flat surface
2. Loosen the screw holding the projector lamp module cover in place and remove the panel
3. Unplug the old projector lamp and remove it from the projector
4. Plug the new projector lamp securely into place
5. Attach the panel back onto the projector and tighten the screw
Installing a Bare Projector Bulb
Every bare projector bulb sold by MyProjectorLamps comes with a detailed instruction sheet with pictures and a clear description of the steps required to install your new lamp. It's an easy process that can be completed in just a few minutes!
To install a bare projector bulb, follow steps 1-2 above and then complete the following:2. Unscrew the wires connected to the bare projector bulb
3. Replace the old lamp with the brand new replacement bulb and fasten the clip
4. Tighten the screws
Resetting The Lamp Hours:
Below are some brief recommendations on how to reset the lamp counter for the most popular projector brands. Please note these are guidelines, for complete installation instructions please consult your projector's manual.
3M Projector Lamps:- Turn on the projector
- Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed
- Select the "RESET" using the "UP" button
- Your lamp counter will now be reset
- Turn on the projector
- Press the "MENU" button and the on-screen menu will appear
- Press 3/4 button to remove the red frame pointer to the Setting Menu Icon
- Press the 6 button to move the red frame pointer to the Lamp Counter Reset item and then press SELECT button
- The message "Reset Lamp Counter?" appears. Move the pointer to "<YES>" and then press SELECT button
- Another confirmation dialog box appears and select "<YES>" to reset the Lamp Replace Counter
- Turn on the projector
- While the projector running, press the MENU button
- Select "OPTION" on the menu using the 5/6 buttons, then press the ENTER button
- Select the "LAMP TIME" using the 5/ 6 buttons, then press and hold the RESET button for 3 seconds
- Select "RESET" using the 5 button
- Turn on the projector
- Press the "MENU" button and the on-screen menu will appear
- Press 3/4 button to remove the red frame pointer to the Setting Menu Icon
- Press the 6 button to move the red frame pointer to the Lamp Counter Reset item and then press SELECT button
- The message "Reset Lamp Counter?" appears. Move the pointer to "<YES>" and then press SELECT button
- Another confirmation dialog box appears and select "<YES>" to reset the Lamp Replace Counter
- Turn on the projector
- Press the "MENU" button and the on-screen menu will appear
- Press 3/4 button to remove the red frame pointer to the Setting Menu Icon
- Press the 6 button to move the red frame pointer to the Lamp Counter Reset item and then press SELECT button
- The message "Reset Lamp Counter?" appears. Move the pointer to "<YES>" and then press SELECT button
- Another confirmation dialog box appears and select "<YES>" to reset the Lamp Replace Counter
- Press "MENU" on the remote or control panel to open the on screen display menu
- Use the 3/4 keys and the section called "Lamp Setting"
- Use the 5/6 keys to select "Lamp Reset"
- Select "YES"
- Turn on the projector
- Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed
- Select the "RESET" using the "UP" button
- Your lamp counter will now be reset
- Turn on the projector
- Press the "MENU" button and the on-screen menu will appear
- Press 3/4 button to remove the red frame pointer to the Setting Menu Icon
- Press the 6 button to move the red frame pointer to the Lamp Counter Reset item and then press SELECT button
- The message "Reset Lamp Counter?" appears. Move the pointer to "<YES>" and then press SELECT button
- Another confirmation dialog box appears and select "<YES>" to reset the Lamp Replace Counter
- Press the MENU button on the projector or remote control
- Use the navigation buttons to open the Reset Menu
- Select the "RESET Lamp Hours"
- When you see the confirmation prompt, highlight "<YES>" and press Enter
- Turn on the projector
- Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed
- Select the "RESET" using the "UP" button
- Your lamp counter will now be reset
- Press "MENU" on the remote or control panel to open the on screen display menu.
- Use the 3/4 keys and the section called "Lamp Setting"
- Use the 5/6 keys to select "Lamp Reset"
- Select "YES"
There are two common methods to reset the lamp counter on InFocus projectors:
Method A:
- Press the decrease volume button on the remote and then the increase volume button within 3 seconds
- The LED light on the projector will turn green
- Turn on the projector
- Turn on the Projector
- Open the standard menu using the remote
- Then select "Setup" or "Service" depending on your projector model
- Then select "Reset Lamp Timer"
- Turn on the projector
- Press the "MENU" button
- Scroll down to "LAMP TIMER RESET", scroll right to enter
- Confirm that it is OK to reset the lamp timer by hitting the OK button
- The on-screen menu should confirm your reset
- Turn on the projector but keep plugged in
- Press the buttons on the control panel in the sequence as below
- Press "Up Arrow", Press "Down Arrow", Press "Left Arrow", Press "Right Arrow", Press "Menu", Press "Enter"
- Lamp time will be reset
- Turn on the projector
- Press the <, > and Power button for about 3 seconds on the control panel
- Lamp hours should be reset
- Press the "OFF" or "HELP" button on the remote control for a minimum of 10 seconds while in standby mode
- The lamp clock is reset to zero the status indicator light will go out
- Press the "POWER" button until an image is projected onto the screen
- Press the "MENU" button to display the main on screen menu and then press the F/G buttons to select "OPTION"
- Press the "ENTER" button to display the "OPTION" menu, and then press the 5/6 buttons to select "LAMP RUNTIME"
- Press and hold the "ENTER" button for approximately 3 seconds
- The "LAMP RUNTIME" will change to "TIME RESET [POWER OFF]"
- The projector will then be powered down
There are two common methods to reset the lamp counter on Proxima projectors:
Method A:
- Press the decrease volume button on the remote and then the increase volume button within 3 seconds
- The LED light on the projector will turn green
- Turn on the projector
- Turn on the Projector
- Open the standard menu using the remote
- Then select "Setup" or "Service" depending on your projector model
- Then select "Reset Lamp Timer"
- Plug the projector in after replacing the lamp
- Press and hold the down arrow along with the "Enter" and "Menu" buttons
- Press "Standby" on the projector control panel while holding the other buttons. Watch the display for "LAMP 0000H" to appear. This indicates the lamp hours are reset. Release the buttons
- Connect the AC power cord to the projector.
- Wait till the ON/STANDBY indicator light is red.
- NOTE: On the remote control, push each button one at a time in the order below for no longer than five seconds.
- Press the Reset button.
- Press the left-arrow button.
- Press the right-arrow button.
- Press the Enter button.
- Turn on the projector
- While holding down "ON/STANDBY", "MENU" and "INPUT" simultaneously, plug the power cord into the mains outlet
- The lamp timer is reset automatically
- Turn on the projector.
- Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed.
- Select the "RESET" using the "UP" button.
Have any questions about selecting or installing replacement lamps? The helpful, knowledgeable staff at MyProjectorLamps is standing by to help! Contact us today via email or at 1-888-785-2677 for help with choosing and installing brand name replacement lamps.